8 Best Swann Security Camera Power Adapter (November 2026)
The best Swann security camera power adapters include the Fancy Buying Security Camera Power Adapter 12V for most Swann camera setups, the TIGERSECU Security Camera Power Adapter with 9-Way for nine standard cameras, and the Gonine Security Camera Power Supply (best with safety protections).
On this page (9 sections)
- Our Swann power adapter picks at a glance
- How the best Swann camera power adapters compare
- How we compared these Swann power adapters
- How do I choose a Swann security camera power adapter?
- What does 12V, 5A and 60 watts mean in daily use?
- How do I install a replacement Swann power adapter?
- Can my Swann cameras work without WiFi?
- How do I keep a camera power adapter running well?
- Verdict: which Swann power adapter should you buy?
The best Swann security camera power adapter for most people is a 12V supply with enough current for the cameras it serves.
Our top pick is the Fancy Buying 12V 5A adapter with an 8-way splitter, because 60 watts covers many standard 12V camera sets from one outlet.
If you only need to power one low-draw camera, a 12V 1A adapter is a simpler and cheaper fit.
If a DVR or PTZ camera pushes the total draw higher, step up to a 7A or 8A supply.
A plug-in camera needs steady DC power to stay online.
Our guide to What Is a Plug in Security Camera, and What It Does? explains why the adapter matters as much as the camera itself.
A weak or undersized adapter can cause reboots, flickering night vision or a camera that drops off the network.
Swann systems that run over wired power often use 12V adapters with barrel connectors.
Some also use Power over Ethernet, which sends power and data on one network cable.
Check your camera label first.
If it says 12V DC, use the adapters in this guide.
If it says PoE, you need a PoE switch or injector instead.
Our picks at a glance
-
1
Best for most Swann camera setupsFancy Buying Security Camera Power Adapter 12V
9.7/10 our score
See it on Amazon -
2
Best for nine standard camerasTIGERSECU Security Camera Power Adapter with 9-Way
9.6/10 our score
See it on Amazon -
3
- 4
Check itYAREMYEYE 12V 7A Security Camera Power Adapter
Best for higher current needs - 5
Check itTIGERSECU 12V 8A Security Camera and DVR
Best for DVR and PTZ loads - 6
Check itTIGERSECU UL Certified 12V 1A Security Camera
Best for two single cameras - 7
Check itSOLTECH [UL Listed] Professional 12V 5A 60W
Best single-adapter replacement - 8
Check itYubunt 12V/1A AC/DC Power Adapter
Best budget 2-pack
Our Swann power adapter picks at a glance
The picks below cover the main jobs.
Multi-camera splitters suit central power points.
Single adapters suit one camera at a time.
Higher-current supplies suit recorders and PTZ cameras.
Our score weighs specs, features and buyer feedback against what Swann owners are shopping for.
Voltage, current, plug size and splitter count drove most of the differences here.
Fancy Buying Security Camera Power Adapter 12V: Best for most Swann camera setups
- 12V 5A output, 60 watts
- 100-240V AC input
- 8-way power splitter cable
- Barrel connector
A 12V 5A adapter with an 8-way splitter for powering several standard cameras or one DVR from a single plug.
Pros
- 60 watts for standard 12V cameras
- 8-way splitter reduces outlet use
- Wide 100-240V input range
Cons
- Splitter cable is not needed for one camera
- Current is shared across connected devices
This pick suits Swann owners who power several standard 12V cameras from one outlet.
The adapter gives 12V at 5A, or 60 watts total, with an 8-way splitter for up to eight cameras or one DVR.
That shared total is the key number in daily use.
Four cameras at 1A each would use 4A, leaving 1A of headroom.
Five cameras at 1A each would use the full rating, which leaves none.
The 100-240V AC input suits homes and offices with standard wall power.
The barrel connector is the common 12V CCTV type.
Fancy Buying lists Lorex, Samsung, Q-See and Night Owl cameras as compatible in its specs, and Swann fits the same standard 12V pattern, but the label on your camera is still the final check.
The trade-off is splitter complexity.
If you only have one camera, the 8-way cable is extra bulk.
If your cameras span several rooms, central power may mean long DC runs that are harder to troubleshoot.
For a clustered set of cameras near one outlet, this is the cleanest first choice.
TIGERSECU Security Camera Power Adapter with 9-Way: Best for nine standard cameras
- 12V 5A output, 60 watts
- 9-way power splitter
- 2.1 x 5.5mm barrel plug
- Swann listed as compatible
A 12V 5A supply with a 9-way splitter for standard analog and HD cameras, with Swann among the brands listed as compatible.
Pros
- Nine outputs for larger camera sets
- Standard 2.1mm plug fits many 12V cameras
- Green indicator light shows power status
Cons
- Not for PTZ cameras, DVRs or NVRs that need higher wattage
- Total load must stay under 60 watts
This pick suits larger Swann sets with standard analog and HD cameras.
It gives 12V at 5A with a 9-way splitter, so one outlet can feed up to nine cameras rated under 60 watts total.
TIGERSECU lists Swann among the compatible brands.
That extra ninth output helps when an 8-way splitter runs out of ports.
The standard 2.1mm DC plug fits many 12V cameras without adapters.
A green indicator light shows that power is flowing.
TIGERSECU also states a magnetic ring to reduce interference between channels and a ground loop isolator in the 3-prong supply.
Those details matter most when cameras share one central power point.
The trade-off is the 60-watt ceiling.
TIGERSECU states this set is not suitable for PTZ cameras, DVRs or NVRs that need higher wattage.
If your Swann system includes a recorder that draws its own power, check its label before assuming this splitter can feed it.
For standard cameras only, the 9-way layout is a strong fit.
Gonine Security Camera Power Supply: Best with safety protections
- 12V 5A output, 60 watts
- 8-way splitter cable
- 100-240V AC input
- Swann listed as compatible
A 12V 5A adapter with an 8-way splitter, a 1.5m AC cord and stated short-circuit, over-voltage and over-current protections.
Pros
- Stated UL, FCC and ETL certifications
- Multiple protection types stated by Gonine
- Includes AC cord and splitter
Cons
- 5.5 x 2.5mm adapter plug differs from some 5.5 x 2.1mm camera plugs
- Shared current across eight outputs
This pick suits Swann owners who want a 5A splitter setup plus stated safety protections.
It gives 12V at 5A, or 60 watts, with an 8-way splitter and a 1.5m AC cord.
Gonine lists Swann among the compatible brands.
The package covers the adapter, the cord and the splitter in one box.
Gonine states UL, FCC and ETL certifications.
It also states short-circuit, over-voltage and over-current protections, plus a built-in safety fuse and flame-retardant ABS plastic.
Those stated protections are a plus for a supply that may run day and night in a closet or attic.
One detail needs care.
Gonine states the adapter plug is 5.5 x 2.5mm while the splitter cables are 5.5 x 2.1mm.
That mix is normal in a kit, but it means you should confirm the plug size on your Swann camera cable before ordering.
A loose barrel fit can cause intermittent power and a warm connection.
YAREMYEYE 12V 7A Security Camera Power Adapter: Best for higher current needs
- 12V 7A output, 84 watts
- 8-way splitter cable
- 100-240V AC input
- Swann listed as compatible
A 12V 7A supply with an 8-way splitter for standard cameras, a DVR, an NVR or an HVR that need up to 84 watts.
Pros
- 84 watts for higher total loads
- 8-way splitter for central power
- Swann listed among compatible brands
Cons
- More power than many single cameras need
- 8-way splitter cable may be unused
This pick suits Swann systems where 5A is not enough.
It gives 12V at 7A, or 84 watts, with an 8-way splitter.
YAREMYEYE lists Swann among the compatible brands.
The extra 24 watts over a 5A supply gives room for more cameras, a DVR, an NVR or an HVR on one central supply.
The 100-240V AC input and standard barrel connection keep setup simple.
The splitter lets you power up to eight cameras or one recorder from a single plug.
For an Analog or AHD system, that can replace several aging wall adapters with one brick.
The trade-off is size and need.
A 7A adapter is more than a single basic camera requires.
If your total camera draw is only 2A or 3A, you are paying for capacity you will not use.
Choose this when the math on your labels adds up past 5A, or when you plan to add cameras soon.
TIGERSECU 12V 8A Security Camera and DVR: Best for DVR and PTZ loads
- 12V 8A output, 96 watts
- 9-way splitter cable
- ETL certification stated
- Swann listed as compatible
A 12V 8A supply with a 9-way splitter designed for standard cameras plus higher-wattage devices such as PTZ cameras, DVRs and NVRs up to 96 watts.
Pros
- 96 watts for DVRs and PTZ cameras
- Nine outputs for larger systems
- ETL certification stated by TIGERSECU
Cons
- Oversized for a single basic camera
- Load must stay at or under 96 watts
This pick suits Swann systems with higher-wattage devices.
It gives 12V at 8A, or 96 watts, with a 9-way splitter.
TIGERSECU lists Swann among the compatible brands.
The set is designed for standard cameras plus devices such as PTZ cameras, DVRs and NVRs up to 96 watts total.
TIGERSECU states ETL certification and a V-0 fire resistance rating.
It also states an anti-jamming magnetic ring and a ground loop isolator to reduce interference and lines across video feeds.
Those features matter when cameras and a recorder share one power point.
The trade-off is plain.
This is the highest-current pick here, so it is oversized for one or two basic cameras.
It also carries a hard limit.
TIGERSECU states not to connect devices that consume more than 96 watts.
Add up every label value, including the recorder, before using this as a central supply.
TIGERSECU UL Certified 12V 1A Security Camera: Best for two single cameras
- 12V 1A output per adapter
- 2-pack, 4.9 ft cables
- UL certification stated
- Swann listed as compatible
A 2-pack of 12V 1A adapters, each rated for a camera under 12 watts, with 4.9-foot cables for adding reach at the camera.
Pros
- Two separate adapters in one set
- 4.9 ft cable adds distance
- UL certification stated by TIGERSECU
Cons
- 1A per adapter does not suit higher-current cameras
- No splitter for multi-camera central power
This pick suits Swann owners replacing power for one or two low-draw cameras.
It is a 2-pack of 12V 1A adapters, each rated for a camera under 12 watts.
TIGERSECU lists Swann among the compatible brands.
Each adapter has a 4.9-foot cable, which adds distance between the outlet and the camera.
The standard 2.1mm DC plug fits many 12V cameras.
TIGERSECU states UL certification and a V-0 fire resistance rating.
A green indicator light shows that the adapter is passing power.
The single-piece cast hardware is designed for a tight, secure connection at the camera.
The trade-off is the 1A limit per adapter.
This set cannot power a DVR, a PTZ camera or a camera that needs more than 1A.
It also has no splitter, so each camera needs its own outlet.
For two basic cameras in separate spots, that simplicity is a plus rather than a minus.
SOLTECH [UL Listed] Professional 12V 5A 60W: Best single-adapter replacement
- 12V 5A output, 60 watts
- UL listed, FCC approved stated
- 47.24 in AC and DC cables
- Swann listed as compatible
A single 12V 5A adapter with long AC and DC cables and stated over-voltage, over-current and over-temperature protections.
Pros
- Long 47.24 in cables
- UL listed and FCC approved as stated by SOLTECH
- Single adapter for one device or a separate splitter
Cons
- No splitter cable included
- 60 watts is shared if you add your own splitter
This pick suits a Swann owner who needs one solid replacement adapter rather than a splitter kit.
It gives 12V at 5A, or 60 watts, as a single adapter.
SOLTECH lists Swann among the compatible brands.
The AC and DC cables are each 47.24 inches long, which helps when the outlet is not right next to the camera.
SOLTECH states UL listing and FCC approval.
It also states over-voltage, over-current and over-temperature protections.
The case uses fire-resistant PC material rated UL 94-V0.
Those stated protections make this a good choice for a recorder or a camera that runs all day.
The trade-off is that no splitter cable is included.
If you want to power several cameras from this adapter, you will need to add a splitter yourself.
The 60-watt total still applies.
Check the 5.5 x 2.1mm connector size against your camera port before ordering, and add up the load if you add a splitter.
Yubunt 12V/1A AC/DC Power Adapter: Best budget 2-pack
- 12V 1A output per adapter
- 2-pack, 1.5m DC cords
- 100-240V AC input
- Swann listed as compatible
A 2-pack of 12V 1A adapters with 1.5m DC cords for cameras that need 12V at 1A or less.
Pros
- Two adapters for two cameras
- 1.5m DC cord per adapter
- FCC and ETL standards stated by Yubunt
Cons
- 1A limit per adapter
- 5.5 x 2.5mm DC head needs a size check against 5.5 x 2.1mm plugs
This pick suits Swann owners who need two basic replacement adapters at a low cost.
It is a 2-pack of 12V 1A adapters with 1.5m DC cords.
Yubunt lists Swann among the compatible brands.
Each adapter is rated for 12 watts, so it fits cameras that need 12V at 1A or less.
Yubunt states over-current, short-circuit, over-voltage and surge protections.
It also states FCC and ETL compliance.
The 100-240V AC input suits standard wall power at home or in a small business.
The trade-off is plug size and current.
Yubunt states the DC head is 5.5 x 2.5mm, while many cameras use 5.5 x 2.1mm.
The outer size is the same, but the center hole differs, so confirm your camera plug first.
This pack also cannot power a DVR or a camera that needs more than 1A.
For two simple cameras, the 2-pack is easy to justify.
How the best Swann camera power adapters compare
The main split is current.
Five picks here give 5A, 7A or 8A for multi-camera setups.
Three picks give 1A per adapter for single cameras.
The right choice depends on the total draw printed on your camera labels.
| Adapter | Output | Splitter | Best fit |
|---|---|---|---|
| Fancy Buying 12V | 12V 5A | 8-way | Most standard Swann sets |
| TIGERSECU 9-Way | 12V 5A | 9-way | Nine standard cameras |
| Gonine | 12V 5A | 8-way | Sets needing stated protections |
| YAREMYEYE | 12V 7A | 8-way | Loads past 5A |
| TIGERSECU 8A | 12V 8A | 9-way | DVR, NVR and PTZ loads |
| TIGERSECU 1A 2-pack | 12V 1A each | None | Two single cameras |
| SOLTECH | 12V 5A | None | One device, long cables |
| Yubunt 2-pack | 12V 1A each | None | Two budget replacements |
| Product | Best for | Output | Input | Splitter | Our score |
|---|---|---|---|---|---|
| Fancy Buying Security Camera Power Adapter 12V | most Swann camera setups | 12V 5A | 100-240V AC | 8-way | 9.7 |
| TIGERSECU Security Camera Power Adapter with 9-Way | nine standard cameras | 12V 5A | 100-240V AC | 9-way | 9.6 |
| Gonine Security Camera Power Supply | with safety protections | 12V 5A | 100-240V AC | 8-way | 9.5 |
| YAREMYEYE 12V 7A Security Camera Power Adapter | higher current needs | 12V 7A | 100-240V AC | 8-way | 9.3 |
| TIGERSECU 12V 8A Security Camera and DVR | DVR and PTZ loads | 12V 8A | 100-240V AC | 9-way | 9.1 |
| TIGERSECU UL Certified 12V 1A Security Camera | two single cameras | 12V 1A | 100-240V AC | 8.8 | |
| SOLTECH [UL Listed] Professional 12V 5A 60W | single-adapter replacement | 12V 5A | 100-240V AC | 8.5 | |
| Yubunt 12V/1A AC/DC Power Adapter | budget 2-pack | 12V 1A | 100-240V AC | 8.2 |
How we compared these Swann power adapters
We compared voltage, current, wattage, plug size, splitter count and stated certifications across all eight picks.
Every pick here runs on 12V DC, because that is what most Swann wired cameras require.
We checked which brands each maker lists as compatible, and Swann appears across this group.
We weighed current headroom against your likely load.
A 5A supply at 60 watts suits many standard camera sets.
A 7A supply at 84 watts and an 8A supply at 96 watts suit recorders and PTZ cameras.
A 1A adapter at 12 watts suits one basic camera only.
We also checked plug size.
Most picks use the standard 2.1mm barrel plug.
Two picks state a 5.5 x 2.5mm head, which needs a quick check against your camera cable.
Polarity should be positive inside and negative outside on standard 12V camera cables.
We did not test these adapters.
We compared specs and stated features, and we flag maker claims as claims.
Our score weighs specs, features and buyer feedback against what Swann owners are shopping for.
How do I choose a Swann security camera power adapter?
The direct answer is to match voltage first, then current, then plug size.
Voltage must match the camera label exactly.
Current must equal or exceed the camera rating.
Plug size and polarity must fit the camera port without looseness.
Start with the label on the camera or its old adapter.
Write down the volts, the amps and the plug size.
For a Swann camera that says 12V 1A, a 12V 1A adapter or a 12V 5A adapter both work.
For a recorder that says 12V 2A, a 1A adapter will not work.
How do I add up current for several cameras?
Add the amp value from every camera and recorder label.
That total is your minimum adapter rating.
A set of four cameras at 1A each needs at least 4A.
A 5A adapter covers that total with 1A to spare.
Why does headroom matter?
Running at the exact limit leaves no room for startup draw or a camera that ages.
A small margin helps the adapter run cooler and more steadily.
If your total is close to 5A, a 7A or 8A supply is the safer pick.
What about adapters for outdoor Swann cameras?
Outdoor cameras need the same voltage and current rules, plus dry placement for the adapter brick.
For cameras mounted outside, our guide to the best power supply for outdoor security camera covers cable routing, weather protection and outlet placement.
What does 12V, 5A and 60 watts mean in daily use?
The direct answer is that 12V is the voltage, 5A is the current limit and 60 watts is the total power.
Multiply volts by amps to get watts.
A 12V 5A adapter gives 60 watts.
A 12V 7A adapter gives 84 watts.
A 12V 8A adapter gives 96 watts.
That total is shared.
Four cameras at 1A each use 48 watts.
A DVR at 2A uses 24 watts by itself.
A PTZ camera can use more than a fixed bullet camera, so check its label rather than guessing.
Heat follows load.
An adapter running near its limit will feel warmer than one running at half load.
Warm is normal for many adapters.
Hot to the touch, a burning smell or repeated shutdowns are signs to reduce the load or replace the supply.
How do splitters share power?
A splitter does not create extra power.
It divides the adapter total across more plugs.
An 8-way or 9-way splitter can feed eight or nine cameras, but only while their combined draw stays under the adapter rating.
Can I mix camera types on one splitter?
Yes, if every device is 12V and the total draw fits.
A fixed camera, a DVR and a PTZ camera can share one supply in theory.
In practice, recorders and PTZ cameras often push the total past 60 watts, which is when a 7A or 8A supply earns its place.
How do I install a replacement Swann power adapter?
The direct answer is to power down, swap the barrel plug, then check each camera before closing up cable runs.
Unplug the old adapter from the wall.
Disconnect it from the camera.
Connect the new adapter, plug it in and confirm the camera comes online.
For a splitter setup, connect the adapter to the splitter first.
Then connect each camera lead to the splitter.
Dress the cables so they do not pull on the barrel plugs.
A loose plug is a common cause of flicker and dropped connections.
Label each lead with tape if you run several cameras to one point.
That step saves time later when one camera drops offline.
Keep the adapter brick in a dry spot with airflow.
Do not seal it in a tight box or bury it under insulation.
What should I check after I install it?
Check that every camera shows a live view.
Check night vision after dark, since infrared LEDs can raise current draw.
Check that plugs sit snug and do not get warm at the connection.
A warm barrel plug often means a loose fit or a load problem.
What if my cameras run on battery or solar?
A wall adapter only helps wired cameras.
Battery and solar models need charge and sunlight, not a 12V brick.
If your Swann cameras are wire-free, check the battery level and solar panel angle instead.
Our best battery backup for security cameras guide covers backup power for outages, and our best battery backup for security camera system guide covers whole-system backup.
Can my Swann cameras work without WiFi?
The direct answer is that power and WiFi are separate jobs.
A wired Swann camera still needs power from an adapter or PoE, even if it records locally to an NVR.
A WiFi camera still needs power, plus a network connection to send alerts or live views.
Our guide to Can Security Cameras Work Without WiFi, and Why It Matters? explains which models record without a network and which ones need one.
Local recording to a DVR or NVR is the usual answer for wired systems.
A replacement adapter does not fix a WiFi problem.
If a camera loses its network but keeps power, check the router and signal strength.
If it loses power entirely, check the adapter, the plug fit and the total load on a shared supply.
How do I keep a camera power adapter running well?
The direct answer is to keep it dry, keep it cool and check the connections twice a year.
Dust the vents with a dry cloth.
Make sure the brick is not pressed against a warm wall or sealed in a cabinet.
Confirm that every barrel plug still seats fully.
Replace an adapter that buzzes loudly, shuts down under light load or has a damaged cord.
Do not tape a frayed cord and keep using it.
A failed adapter is cheaper than a damaged camera or recorder.
What is the best security camera power supply for a basic setup?
For a basic setup, a 12V adapter with enough current for your cameras is the right answer.
Our broader guide to the best security camera power supply covers single adapters, splitters and PoE options across brands.
Use this Swann guide to narrow that list to your voltage, current and plug size.
Verdict: which Swann power adapter should you buy?
The best Swann security camera power adapter for most owners is the Fancy Buying 12V 5A adapter with the 8-way splitter.
It covers standard 12V cameras from one outlet with 60 watts to share.
Choose the TIGERSECU 9-way model if you need a ninth output.
Choose the Gonine model if stated safety protections matter most to you.
Pick the YAREMYEYE 7A or TIGERSECU 8A supply if your labels add up past 5A.
That includes systems with a DVR, an NVR or a PTZ camera on the same supply.
Pick the TIGERSECU 1A 2-pack or the Yubunt 2-pack if you only need to power one or two basic cameras from separate outlets.
Before you order, check three things on your camera label.
Confirm 12V DC.
Confirm the amp rating.
Confirm the barrel plug size and polarity.
Match those three, and any adapter in this guide will be a clean replacement for your Swann system.
For more context on wired versus wire-free power, start with our best security camera power supply guide and match the adapter to your camera label.
Our top 3 picks at a glance
-
1
Best for most Swann camera setupsFancy Buying Security Camera Power Adapter 12V
9.7/10 our score
See it on Amazon -
2
Best for nine standard camerasTIGERSECU Security Camera Power Adapter with 9-Way
9.6/10 our score
See it on Amazon -
3
Frequently asked questions
How do I know if a replacement adapter fits my Swann camera?
Check three things first. The camera label should call for 12V DC.
The old adapter should show the current it supplies, such as 1A or 2A.
The barrel plug should match in size and polarity, commonly 5.5 x 2.1mm with positive inside and negative outside.
A replacement with the same voltage and equal or higher current rating is the usual starting point.
Can one adapter power several Swann cameras?
Yes, if the cameras are 12V and their combined current stays under the adapter rating. A 12V 5A adapter supplies 60 watts total, shared across every connected camera.
Add up each camera label value before using a splitter, and leave headroom rather than running at the exact limit.
Why does my Swann camera lose power after I add more cameras?
A shared adapter is often overloaded when cameras are added. Each camera draws part of the total current, so a supply that worked for two cameras may fail with five.
Check the combined draw against the adapter rating, and move to a higher-current supply or separate adapters if the total exceeds the limit.
Do I need a splitter cable or a single adapter?
A single adapter suits one camera or one recorder. A splitter suits several cameras that share one nearby outlet.
If your cameras are in different rooms, individual adapters keep cable runs shorter and make fault finding easier.
What plug size do Swann cameras use?
Many 12V Swann cameras use a standard barrel plug, often 5.5 x 2.1mm. Some adapters use 5.5 x 2.5mm, which has the same outside diameter but a larger center hole.
Measure the old plug or check the label before ordering, because a loose fit can cause flicker and heat at the connection.
About this guide: Our look at Swann security camera power adapters draws on maker specs, materials and what owners report. See how we research.



