Best picks

9 Best Ethernet Cables for Security Cameras (November 2026)

Updated on · By the Get Security Camera team

The best ethernet cable for security cameras include the Ultra Clarity Cables Cat6 Ethernet Cable 100 FT for most PoE camera runs, the Adoreen Cat 6 Outdoor Ethernet Cable for direct burial outdoor runs, and the Swann Security Cat5 Ethernet Cable for Swann NVR extensions.

On this page (9 sections)
  1. How we compared these ethernet cables for security cameras
  2. The best ethernet cable for security cameras: our 9 picks
  3. Which security camera ethernet cable should you buy?
  4. How do I choose the right length for a PoE camera cable?
  5. Cat5e or Cat6: which is better for PoE security cameras?
  6. Indoor, outdoor or direct burial: what does your route need?
  7. How do you install a security camera ethernet cable?
  8. Can security cameras work without WiFi?
  9. Verdict: which ethernet cable for security cameras should you buy?

The best ethernet cable for security cameras is the Ultra Clarity Cables Cat6 Ethernet Cable 100 FT, because a 100 ft Cat6 run with RJ45 connectors covers most PoE camera placements. Our score weighs specs, features and buyer feedback against what you are shopping for.

Choose the Adoreen for burial, the Swann cable for a Swann NVR, or the REOLINK 60 ft cable when your camera sits close to the recorder.

A security camera ethernet cable does two jobs at once. It carries video data back to your recorder or network, and on a PoE system it carries power to the camera.

That is why one cable per camera keeps the install simple. You avoid a separate power cord at each camera point.

Start with length. Measure the route from recorder or switch to camera, then add slack for corners, drops and connector space.

A cable that comes up short is hard to fix. A cable with extra length can be coiled neatly.

If you want the broader view first, our best cable for security cameras guide covers coax, power and Ethernet options side by side. This roundup stays focused on Ethernet and PoE cables only.

Our picks at a glance

  1. 1 Ultra Clarity Cables Cat6 Ethernet Cable 100 FT
    Best for most PoE camera runs

    Ultra Clarity Cables Cat6 Ethernet Cable 100 FT

    9.7/10 our score

    See it on Amazon
  2. 2 Adoreen Cat 6 Outdoor Ethernet Cable
    Best for direct burial outdoor runs

    Adoreen Cat 6 Outdoor Ethernet Cable

    9.6/10 our score

    See it on Amazon
  3. 3 Swann Security Cat5 Ethernet Cable
    Best for Swann NVR extensions

    Swann Security Cat5 Ethernet Cable

    9.5/10 our score

    See it on Amazon
  1. 4ZOSI Cat5e Ethernet Cable 100ft

    ZOSI Cat5e Ethernet Cable 100ft

    Best for ZOSI PoE camera systems
    Check it
  2. 5Amcrest CAT6E 4K-Rated Video POE Ethernet Cable

    Amcrest CAT6E 4K-Rated Video POE Ethernet Cable

    Best for a four camera Amcrest bundle
    Check it
  3. 6REOLINK RJ45 Cat-5 60 Feet Network EthernetCheck it
  4. 7GWFIBER cat 6 ethernet Cable 100 ft

    GWFIBER cat 6 ethernet Cable 100 ft

    Best for waterproof outdoor couplers
    Check it
  5. 8REOLINK RJ45 Cat-5 100 Feet Network EthernetCheck it
  6. 9OOSSXX 4 x 60 Feet Ethernet Cable

    OOSSXX 4 x 60 Feet Ethernet Cable

    Best for four short camera drops
    Check it

How we compared these ethernet cables for security cameras

We compared length, category, gauge, connector type, jacket and outdoor rating, and what each cable is made to work with. We looked at whether a cable suits a single camera or a multi camera system.

We also checked what is in the box, such as adapters, ties or a four pack.

The best ethernet cable for security cameras: our 9 picks

The Ultra Clarity Cables cable leads for a general single camera run. The rest of the list splits by brand system, length and outdoor build.

Pick by your route first, then by category.

1

Ultra Clarity Cables Cat6 Ethernet Cable 100 FT: Best for most PoE camera runs

Ultra Clarity Cables Cat6 Ethernet Cable 100 FT, ethernet cable for security cameras
9.7/10Our score
  • 100 ft Cat6 cable
  • 500 MHz and 10 Gbps
  • 24 AWG solid copper conductors
  • RJ45 gold-plated contacts
  • Indoor and outdoor use

A 100 ft Cat6 cable with RJ45 connectors for a single long PoE camera run, with indoor and outdoor use.

See it on Amazon

Pros

  • 100 ft length for distant cameras
  • Cat6 500 MHz performance
  • Molded strain relief boots

Cons

  • One cable per pack
  • 5.8 mm PVC jacket needs routing space

Ultra Clarity Cables suits a single distant PoE camera where you want Cat6 headroom in one 100 ft run. It uses 8 solid copper conductors at 24 AWG, with 4 unshielded twisted pairs separated by PE cross insulation.

That build matters in daily use because 24 AWG conductors carry PoE power better than thinner wire on a long run.

The jacket is 5.8 mm PVC with RJ45 connectors and gold plated contacts. Molded strain relief boots help at the plug, where cables usually take the most strain during install and later adjustment.

The cable is rated for indoor and outdoor use.

Ultra Clarity Cables says it supports 500 MHz and 10 Gbps, and it is backward compatible with Cat5e and earlier networks. For a camera, that means you do not need to worry about the cable limiting a standard PoE camera feed.

The trade off against the Adoreen is outdoor build. This is a general indoor and outdoor patch cable, not a direct burial cable with a double jacket.

Choose it for walls, ceilings and eaves. Choose a burial rated cable for underground runs.

Ultra Clarity Cables Cat6 Ethernet Cable 100 FTCheck it on Amazon
2

Adoreen Cat 6 Outdoor Ethernet Cable: Best for direct burial outdoor runs

Adoreen Cat 6 Outdoor Ethernet Cable, ethernet cable for security cameras
9.6/10Our score
  • 100 ft Cat6 outdoor cable
  • Double jacket with UV resistant LLDPE outer jacket
  • Direct burial use
  • 24 AWG solid CCA conductors
  • RJ45 connectors
  • 25 ties included

A sturdy 100 ft outdoor Cat6 cable with a double jacket for burial or conduit runs to a PoE camera.

See it on Amazon

Pros

  • Double jacket for outdoor burial
  • Direct burial rated
  • 25 ties included

Cons

  • Stiff cable by design
  • Conductors are copper clad aluminum

Adoreen suits a camera run that crosses soil, conduit or open outdoor space. It has a double jacket, with a UV resistant LLDPE outer jacket for outdoor and direct buried install.

That second jacket is the key difference from the general purpose Cat6 picks above.

The cable is 100 ft of Cat6 with 4 twisted pairs of solid CCA conductors at 24 AWG and gold plated RJ45 connectors. A PVC cross separator reduces noise between pairs.

Adoreen says it can support PoE cameras, and the solid 24 AWG conductors help on a 100 ft PoE run.

In daily use, the stiff build is a trade off. Adoreen notes the cable is a little stiff as a result of being sturdy.

That stiffness helps outdoors, but it needs more care at tight bends and at the camera end. Plan a gentler bend radius than you would with a flexible indoor patch cord.

Against the Ultra Clarity Cables pick, you trade flexible routing for burial strength. Against the GWFIBER pick, Adoreen gives you a 2 year warranty and 25 ties in the box.

Pick Adoreen when the route is the hard part of the job.

Adoreen Cat 6 Outdoor Ethernet CableCheck it on Amazon
3

Swann Security Cat5 Ethernet Cable: Best for Swann NVR extensions

Swann Security Cat5 Ethernet Cable, ethernet cable for security cameras
9.5/10Our score
  • 100 ft/30 m Cat5 cable
  • For Swann NVR systems
  • RJ45 extension adapter included
  • UL certified with VW-1 rating
  • Power, video and audio over one cable

A 100 ft Swann Cat5 extension cord with an RJ45 adapter to add distance to a Swann PoE camera.

See it on Amazon

Pros

  • Made for Swann NVR systems
  • Adapter included in the box
  • One cable for power and video

Cons

  • Cat5 rather than Cat6
  • Best matched to Swann systems

Swann suits owners who already run a Swann NVR and need to add length beyond a camera's own cable. This is a 100 ft/30 m Cat5 extension cord with an RJ45 extension adapter in the box.

It adds distance to a shorter cable rather than replacing every cable in the system.

Swann says power, video and audio run through a single Ethernet cable per camera. That one cable design is what makes PoE NVR installs simpler than separate power and video runs.

The cable is UL certified with a VW-1 rating for fire resistance.

In daily use, the adapter is the part to plan around. Keep the joint in a dry, accessible spot if you can.

A joint hidden in a wall void is hard to check later if a camera drops offline. Route the adapter where you can reach it.

The trade off is category and brand fit. This is Cat5, not Cat6, and Swann says it is compatible with all Swann NVRs.

If you run Swann cameras, that fit is a plus. If you run another brand, a general Cat5e or Cat6 cable gives you more choice.

For more brand detail, see our best swann security camera cables guide.

Swann Security Cat5 Ethernet CableCheck it on Amazon
4

ZOSI Cat5e Ethernet Cable 100ft: Best for ZOSI PoE camera systems

ZOSI Cat5e Ethernet Cable 100ft, ethernet cable for security cameras
9.2/10Our score
  • 100 ft Cat5e cable
  • RJ45 connectors
  • PoE compatible for security cameras
  • Waterproof indoor outdoor use
  • 100 MHz

A 100 ft Cat5e RJ45 cable for PoE security cameras, NVRs and PoE switches in indoor or outdoor runs.

See it on Amazon

Pros

  • 100 ft for hard to reach cameras
  • PoE data and power in one cable
  • Indoor and outdoor use

Cons

  • Cat5e rather than Cat6
  • Grey color may show dirt outdoors

ZOSI suits a PoE camera, NVR or PoE switch setup where a single 100 ft Cat5e run needs to reach a hard to reach camera. It supports up to 1000 Mbps, which is well above what a typical PoE camera feed needs.

The point of the cable is reach and reliability, not top end network speeds.

The cable delivers both power and data to PoE devices. That means no extra power cord at the camera if your switch, injector or NVR supplies PoE.

ZOSI describes premium shielding and sturdy construction for stable performance in home, office or outdoor setups.

In daily use, the 100 ft length helps with cameras on a far corner of a house, a barn or a detached garage. Measure the full route before you order, because adding a second cable later means another joint.

A single continuous run looks cleaner and has fewer points of failure.

The trade off against Cat6 picks is headroom. Cat5e at 100 MHz is fine for most PoE cameras, but Cat6 gives more margin on long or noisy routes.

Pick ZOSI for a ZOSI PoE system or a general PoE run where Cat5e fits. Pick Cat6 when you want the extra spec margin.

ZOSI Cat5e Ethernet Cable 100ftCheck it on Amazon
5

Amcrest CAT6E 4K-Rated Video POE Ethernet Cable: Best for a four camera Amcrest bundle

Amcrest CAT6E 4K-Rated Video POE Ethernet Cable, ethernet cable for security cameras
9.0/10Our score
  • 100 ft Cat6e cable
  • 4 pack
  • RJ45 8P8C connectors
  • 28 AWG
  • 250 MHz and 1000 Mbps
  • Indoor and outdoor use

A four pack of 100 ft Cat6e cables with RJ45 connectors for PoE IP cameras, one cable per camera.

See it on Amazon

Pros

  • Four cables for a multi camera system
  • 100 ft per camera
  • One cable for power and video

Cons

  • 28 AWG is thinner than 24 AWG
  • Four pack is more than a single camera needs

Amcrest suits a multi camera install where you need one 100 ft cable per camera and want to buy them together. This is a 4 pack of 100 ft Cat6e cables with RJ45 8P8C connectors.

Four cameras get four matched cables, which keeps the install uniform.

Amcrest says the cable carries power, video and audio over one Ethernet cable, so one run per camera can handle the full feed. It supports bandwidth up to 250 MHz and speeds up to 1000 Mbps.

That spec suits PoE IP cameras as well as a router, laptop or smart TV run.

In daily use, the four pack saves repeat orders. If you add a camera later, you may still need another cable, but the first four are covered.

The red color also makes each run easy to trace back to the recorder during setup.

The trade off is wire gauge. The conductors are 28 AWG, which is thinner than the 24 AWG wire in the Ultra Clarity Cables and Adoreen picks.

On a 100 ft PoE run, thinner wire has more resistance, so check that your PoE switch or injector is rated for the full length of your cameras. If your runs are short, the four pack is a clean buy.

If your runs are long, a 24 AWG Cat6 cable may be the safer match.

Amcrest CAT6E 4K-Rated Video POE Ethernet CableCheck it on Amazon

REOLINK suits a nearby PoE camera where 60 ft is enough to reach from a Reolink NVR, injector or switch. It is a 60 ft Cat5 cable with RJ45 connectors using T-568B wiring.

The shorter length fits a typical home run without a large coil of spare cable.

Reolink says the cable transmits power and signal over one cable, and it suits all Reolink PoE cameras and NVRs. Plug it into a PoE injector or Reolink NVR and the camera connects through the app.

That plug and play setup helps if this is your first wired camera.

In daily use, 60 ft works well for a camera on the same wall as the recorder, a short run to a porch or a garage close to the house. It is less suited to a far corner or a detached building.

Measure first, because a 60 ft cable that is 10 ft short cannot be stretched.

The trade off is length and category. The 100 ft REOLINK cable in this list covers longer runs, and Cat6 picks give more spec headroom.

Pick this 60 ft cable for a short Reolink run. Pick the 100 ft version when the camera sits farther away.

REOLINK RJ45 Cat-5 60 Feet Network EthernetCheck it on Amazon
7

GWFIBER cat 6 ethernet Cable 100 ft: Best for waterproof outdoor couplers

GWFIBER cat 6 ethernet Cable 100 ft, ethernet cable for security cameras
8.4/10Our score
  • 100 ft Cat6 cable
  • RJ45 connectors
  • Waterproof coupler
  • Indoor and outdoor use
  • 250 MHz

A 100 ft Cat6 cable with a waterproof coupler for outdoor PoE IP camera use, with indoor use as well.

See it on Amazon

Pros

  • Waterproof coupler included
  • 100 ft for long outdoor runs
  • Cat6 and backward compatible with Cat5 and Cat5e

Cons

  • Single cable per pack
  • Waterproof lid needs correct seating to work

GWFIBER suits an outdoor PoE IP camera where the cable joint needs weather protection. It is a 100 ft Cat6 cable with a waterproof coupler.

The coupler adds a weather seal at the connection point, which is where outdoor runs often fail over time.

The cable is Cat6 and backward compatible with Cat5 and Cat5e, so it fits standard RJ45 camera ports. GWFIBER says the copper core meets the Cat6 standard at 0.56 mm to 0.58 mm.

It is rated for indoor and outdoor use, with a length range from 0.5 meters to 30 meters in the size options.

In daily use, the waterproof lid needs care. Seat it fully and check it after install, because a partially seated lid will not seal.

Route the joint so water runs off rather than pooling inside the coupler.

The trade off against the Adoreen is the outdoor approach. Adoreen uses a double jacket for burial and conduit.

GWFIBER uses a waterproof coupler for a camera connection. Pick GWFIBER for an outdoor camera joint.

Pick Adoreen for a run that goes underground.

GWFIBER cat 6 ethernet Cable 100 ftCheck it on Amazon

REOLINK suits a distant Reolink PoE camera in a large home, a multi story building or a remote camera point. It is a 100 ft Cat5 cable with RJ45 connectors using T-568B wiring, built for power and signal over one cable.

The extra length over the 60 ft REOLINK cable covers far corners and upper floors.

Reolink says it suits all Reolink PoE cameras and NVRs, and it works with a PoE injector or Reolink NVR. The cable is designed for reliable Ethernet performance with wear and bending resistance, for indoor and outdoor routing.

In daily use, a 100 ft run gives you slack to route around corners, through a wall void or up to a high mount. Coil any spare length in a loop with a wide bend radius.

Tight bends can stress the conductors and the plug.

The trade off is category. This is Cat5, while several picks above are Cat6.

For a Reolink system, brand fit may matter more than the extra Cat6 spec. Reolink also notes the system is designed to work exclusively with Reolink PoE cameras for full function.

If you run Reolink, this is a direct match. If you run another brand, check camera compatibility first.

REOLINK RJ45 Cat-5 100 Feet Network EthernetCheck it on Amazon
9

OOSSXX 4 x 60 Feet Ethernet Cable: Best for four short camera drops

OOSSXX 4 x 60 Feet Ethernet Cable, ethernet cable for security cameras
8.0/10Our score
  • 4 cables at 60 ft each
  • RJ45 connectors with gold plated pins
  • 24 AWG stranded conductors
  • 150 MHz
  • Indoor and outdoor use
  • Flexible PVC jacket

A four pack of 60 ft Ethernet cables with RJ45 connectors for four PoE cameras or devices near your router or NVR.

See it on Amazon

Pros

  • Four cables in one box
  • 60 ft suits nearby cameras
  • Gold plated RJ45 contact pins

Cons

  • Lowest score in this group
  • 60 ft may be short for distant cameras

OOSSXX suits a four camera setup where each camera sits within 60 ft of the recorder or switch. This is a 4 pack of 60 ft Ethernet cables with RJ45 connectors and gold plated contact pins.

Four matched cables cover a typical small system in one box.

The cables use 4 twisted pairs of 24 AWG stranded conductors, separated by PE cross insulation to reduce crosstalk. OOSSXX states a high bandwidth of 150 MHz.

Stranded conductors are flexible, which helps in daily use when you route a cable through bends, clips and tight spaces.

The cable fits PoE security cameras, NVRs, switches, routers, computers and smart TVs with RJ45 ports. It is rated for indoor and outdoor use with a flexible PVC jacket.

OOSSXX says each cable goes through rigorous testing before delivery.

The trade off is length and score. At 60 ft per cable, this pack will not reach a far camera.

The four pack also asks you to route four separate cables, which takes more planning than one long run. Pick OOSSXX for four nearby cameras.

Pick a 100 ft single cable for one distant camera.

OOSSXX 4 x 60 Feet Ethernet CableCheck it on Amazon

Which security camera ethernet cable should you buy?

The Ultra Clarity Cables Cat6 cable is the best ethernet cable for security cameras for most single camera runs. It gives you 100 ft, Cat6 specs, 24 AWG solid copper conductors and RJ45 connectors in one cable.

That mix fits a wide range of PoE cameras.

Brand systems change the pick. Swann owners should look at the Swann Cat5 extension cord first, because it is made for Swann NVRs and includes the adapter.

Reolink owners should match the 60 ft or 100 ft REOLINK cable to the run length. Amcrest owners who need four cameras at once should look at the four pack.

Outdoor route changes the pick again. A burial or conduit run needs the Adoreen double jacket.

An outdoor camera joint needs the GWFIBER waterproof coupler. A short indoor run needs neither.

ProductBest forLengthCategoryConnectorOur score
Ultra Clarity Cables Cat6 Ethernet Cable 100 FTmost PoE camera runs100 ftCat 6RJ459.7
Adoreen Cat 6 Outdoor Ethernet Cabledirect burial outdoor runs100 ftCat 6RJ459.6
Swann Security Cat5 Ethernet CableSwann NVR extensions100 ft/30 mCat5RJ459.5
ZOSI Cat5e Ethernet Cable 100ftZOSI PoE camera systems100 ftCat 5eRJ459.2
Amcrest CAT6E 4K-Rated Video POE Ethernet Cablea four camera Amcrest bundle100 ftCat 6RJ459.0
REOLINK RJ45 Cat-5 60 Feet Network Ethernetshort Reolink runs60 ftCat 5RJ458.7
GWFIBER cat 6 ethernet Cable 100 ftwaterproof outdoor couplers100 ftCat 6RJ458.4
REOLINK RJ45 Cat-5 100 Feet Network Ethernetlong Reolink runs100 ftCat 5RJ458.2
OOSSXX 4 x 60 Feet Ethernet Cablefour short camera drops60 ft eachCat 6RJ458.0

How do I choose the right length for a PoE camera cable?

Measure the full route, then add slack for corners, drops and connectors. A 100 ft cable works for most home camera runs.

A 60 ft cable works when the camera sits near the recorder.

Start at the recorder or PoE switch and follow the path you will actually run. Go up a wall, across a ceiling, out an eave and down to the mount.

Each change of direction uses cable. Add at least a few feet of slack at each end for the plug and the camera port.

If your route crosses a building, measure each section. A run from a house to a garage may need the full 100 ft even when the straight line distance looks short.

Straight line distance is not cable distance.

When is 60 ft enough?

60 ft is enough for a camera on the same wall as the recorder, a porch near the router, or a garage close to the house. The REOLINK 60 ft cable and the OOSSXX 60 ft pack fit this case.

When should you choose 100 ft?

Choose 100 ft for a far corner, a second story mount, a barn, a detached garage or any route with several corners. Most picks in this roundup are 100 ft for this reason.

A longer cable with a neat coil beats a short cable with a joint.

Cat5e or Cat6: which is better for PoE security cameras?

Cat5e is enough for most PoE camera runs at 100 ft. Cat6 gives more headroom for long runs and noisy routes.

Both use RJ45 connectors and both can carry PoE power and data.

Cat5e is rated at 100 MHz. Cat6 is rated up to 500 MHz in the Ultra Clarity Cables cable.

Higher frequency ratings help with signal quality on longer runs. For a camera feed, the practical difference shows up over distance and in a busy network, not in a short patch cord.

Gauge matters as much as category for PoE. A 24 AWG cable, such as the Ultra Clarity Cables and Adoreen picks, carries power with less resistance than a 28 AWG cable, such as the Amcrest four pack.

On a 100 ft run, that difference can matter for camera power.

If you are wiring a new system, Cat6 is the safer default when the price is close. If you already have Cat5e in the walls and it works, there is no need to replace it.

Our best cable for security cameras guide covers the wider cable choice.

Cat5e picks in this list

The ZOSI Cat5e cable and the REOLINK Cat5 cables suit standard PoE camera runs. They cover 60 ft and 100 ft lengths with RJ45 connectors.

Cat6 picks in this list

The Ultra Clarity Cables, Adoreen, GWFIBER and OOSSXX cables are Cat6. The Amcrest cable is labeled Cat6e.

These give more spec margin for long or multi camera runs.

Indoor, outdoor or direct burial: what does your route need?

Match the jacket to the route. Indoor cables are for walls and ceilings.

Outdoor cables are for eaves, fences and open runs. Direct burial cables are for underground runs.

An indoor cable exposed to sun and rain will degrade faster. Its jacket is not built for UV, moisture and temperature swings.

An outdoor cable has a jacket for those conditions. The Adoreen cable goes further with a double jacket for burial and conduit.

A waterproof coupler, such as the one on the GWFIBER cable, protects a joint. It does not replace a cable with the right jacket.

If the whole run sits outdoors, the cable itself should be outdoor rated.

If your camera needs a separate power cable instead of PoE, our best security camera power cable guide covers that route. PoE cables carry power and data together, so most wired camera installs do not need both.

Indoor runs

Use an indoor rated cable for attic, ceiling and in wall runs. Keep it away from heat sources and sharp edges during install.

Outdoor and burial runs

Use an outdoor rated cable for eaves, poles and fence lines. Use a direct burial cable, such as the Adoreen pick, for underground runs.

Add a waterproof coupler at exposed joints.

How do you install a security camera ethernet cable?

Run one cable per camera from the PoE switch, injector or NVR to the camera. Test the camera at ground level before you mount it high.

Label both ends of each cable.

Start with the camera on the ground or a ladder. Plug in the cable, confirm video and PoE power, then mount the camera.

That order saves you from pulling a cable down after a mistake.

Route the cable with wide bends. Use clips or staples made for cable, and avoid crushing the jacket.

Keep the cable away from power lines where you can, to reduce noise on the feed.

If you need more reach than one cable gives, our best security camera extension cable guide covers extension options. Keep joints accessible and dry.

If a camera uses a plug instead of PoE, our What Is a Plug in Security Camera, and What It Does? guide explains the trade off.

Connectors and joints

Use RJ45 connectors that match the cable. Seat each plug fully and check the latch.

A good connector choice helps as much as a good cable, so see our best security camera cable connectors guide before you crimp or join cables.

Test before you mount

Confirm live video, recording and camera power before final mounting. Check the camera at night as well as in daylight if you can.

A cable fault often shows as a camera that drops offline.

Can security cameras work without WiFi?

Yes. A wired PoE camera can record to an NVR without WiFi.

The Ethernet cable carries the video feed to the recorder and the power to the camera. WiFi is only needed for remote viewing in many systems.

That wired design is why a good Ethernet cable matters. A stable cable gives you a stable recording path.

Our Can Security Cameras Work Without WiFi, and Why It Matters? guide covers when WiFi is needed and when it is not.

For brand specific cable choices, our best lorex security camera cables guide covers Lorex systems in the same way this post covers Swann, ZOSI, Amcrest and REOLINK.

Verdict: which ethernet cable for security cameras should you buy?

Pick the Ultra Clarity Cables Cat6 Ethernet Cable 100 FT for a general PoE camera run. Pick the Adoreen for burial, the Swann cable for a Swann NVR, and the REOLINK 60 ft or 100 ft cable for a Reolink system.

Measure your route first. Then match the jacket to the route and the length to the longest run.

One good cable per camera will keep your system simple and your recordings steady.

Our top 3 picks at a glance

  1. 1 Ultra Clarity Cables Cat6 Ethernet Cable 100 FT
    Best for most PoE camera runs

    Ultra Clarity Cables Cat6 Ethernet Cable 100 FT

    9.7/10 our score

    See it on Amazon
  2. 2 Adoreen Cat 6 Outdoor Ethernet Cable
    Best for direct burial outdoor runs

    Adoreen Cat 6 Outdoor Ethernet Cable

    9.6/10 our score

    See it on Amazon
  3. 3 Swann Security Cat5 Ethernet Cable
    Best for Swann NVR extensions

    Swann Security Cat5 Ethernet Cable

    9.5/10 our score

    See it on Amazon

Frequently asked questions

What is the best cable for PoE security cameras?

A Cat5e or Cat6 cable with RJ45 connectors is the usual choice for PoE security cameras. It carries video data and PoE power over one cable to the camera.

Pick the length for your longest run, then choose indoor, outdoor or direct burial build for the route.

Can a security camera ethernet cable carry power?

Yes. A PoE security camera cable carries both data and power over the same Ethernet cable.

That is why one Cat5e or Cat6 run can feed a PoE camera from a PoE switch, injector or NVR.

A non PoE camera still needs its own power supply.

Do I need Cat6 or is Cat5e enough?

Cat5e is enough for most PoE camera runs at 100 ft. Cat6 adds headroom with higher frequency ratings.

Choose Cat6 when the run is long, the route is noisy, or you want extra margin for future cameras.